EMC China Lab

ISO 10993 Biocompatibility Cytotoxicity Test

Views :
Update time : 2024-10-08

Cytotoxicity Test Introduction

Cytotoxicity evaluates the toxic responses of potential bioactive substances in material extracts to cultured mammalian cells ().

The principle is that the yellow aqueous solution MTT is metabolically reduced in living cells to generate insoluble formazan. The number of living cells is related to the colorimetry of the formazan after it is dissolved in alcohol and measured by a photometer.

ISO 10993 Biocompatibility Cytotoxicity Test(图1)


Cytotoxicity Test standards

2.1 GB/T 16886.5-2022 Biological evaluation of medical devices Part 5: In vitro cytotoxicity test;

2.2 ISO 10993-5:2009 Biological evaluation of medical devices—Part 6: Tests for in vitro cytotoxicity。

3. Test system

L929 cells.

4. Preparation of test samples

The extract was prepared according to GB/T 16886.12.

ISO 10993 Biocompatibility Cytotoxicity Test(图2)


5. Test steps

5.1 Cell culture preparation

The cultured cells were removed from the culture flask by enzymatic digestion (trypsin/EDTA) and the cell suspension was centrifuged at 200 g for 3 min. The cell suspension was resuspended in culture medium to adjust the density to 1 × 105 cells/mL and 100 μL of culture medium was added to the peripheral wells of a 96-well tissue culture microtiter plate (= 1 × 104 cells/well) using a multichannel pipette.

The cells were incubated for 24 h to form a semi-confluent monolayer. The culture was incubated in a CO2 incubator (37°C ± 1°C, humidity > 90%) with a 5 ± 1% atmosphere for (24 ± 2) h to allow the cells to grow to form a nearly confluent monolayer.

5.2 Contact training

After 24 hours of incubation, aspirate the culture medium from the plate wells and add 100 μL of the test sample extract, control sample extract, blank control solution and positive control solution. All doses need to be done in at least six parallels. Add the blank to the left (column 2) and right (column 11) sides of the 96-well plate. Then incubate for 24 hours ± 2 hours at (37 ± 1) ° C, 5 ± 1% CO2, and humidity > 90%.

5.3 Observation

After 24 hours of incubation, examine each plate under a phase contrast microscope to determine the systematic errors in cell seeding and the growth characteristics of the control and test cells. Record changes in cell morphology caused by the cytotoxic effects of the test sample extracts, but these records are not used in any quantitative determination of cytotoxicity. Poor growth characteristics of the control cells may indicate experimental errors and the test may be abandoned as a result.

5.4 Add MTT

After checking the cell growth in the plate wells, carefully remove the culture medium from the plate wells, add 50 μL of MTT solution (prepared to 1 mg/mL with complete MEM culture medium without phenol red) to each test plate well, and culture at (37 ± 1) ℃ for (2 ± 0.2) h. Discard the MTT solution, add 100 μL of isopropanol to each well to dissolve the formazan, shake the plate, and then measure the absorbance value of each well at a wavelength of 570 nm (reference wavelength 650 nm).

5.4 Data Analysis

The reduction in the number of viable cells results in a decrease in metabolic activity in the sample, which is directly related to the amount of blue-violet formazan produced. The reduction in cell viability of the test sample compared to the blank control ( cells directly in contact with the extraction medium ) can be calcULated using the following formula:

MICrosoft YaHei", "Microsoft YaHei UI", "WenQuanYi Micro Hei", "sans-serif", 宋体; font-optical-sizing: inherit; font-kerning: inherit; font-feature-settings: inherit; font-variation-settings: inherit; margin-top: 0px; margin-bottom: 0px; padding: 0px; color: rgb(51, 51, 51); box-sizing: border-box; text-wrap: wrap; background-color: rgb(255, 255, 255);">

Where: OD570e---the average absorbance value measuRED for the test sample, positive control and negative control groups.

OD570b---average absorbance value of the blank control group (cells directly in contact with the extraction medium).

When the survival rate is low, the potential cytotoxicity of the test sample is high. If the survival rate decreases by less than 70% of the blank, the fish oil is potentially cytotoxic. The survival rate of the 50% extract of the test sample is the same or higher, otherwise the test should be repeated.

ISO 10993 Biocompatibility Cytotoxicity Test(图3)



Email:hello@jjrlab.com


Leave Your Message


Write your message here and send it to us


Related News
Read More >>
Biodegradable Plastic Testing Services Biodegradable Plastic Testing Services
03 .10.2026
Plastic pollution drives global regulations; JJR LAB provides comprehensive biodegradable plastic te...
Introduction to INMETRO Certification for Toy Expo Introduction to INMETRO Certification for Toy Expo
03 .10.2026
INMETRO cert covers toys’ mechanical, flammability, chemical, electric, laser safety (ABNT NM 300-1/...
Toy Export Compliance Testing Starting from $538 p Toy Export Compliance Testing Starting from $538 p
03 .10.2026
JJR LAB offers Toy Export Compliance Testing from $538/model for EU EN71, US ASTM F963 & AS/NZS ...
Amazon DV  : Adult Bed Safety Rails, Clothing Stor Amazon DV : Adult Bed Safety Rails, Clothing Stor
03 .09.2026
Amazon DV now mandates adult bed rails (ASTM F3186), clothing storage (ASTM F2057), and walkers (ISO...
What Certifications Are Required to Sell Air Fryer What Certifications Are Required to Sell Air Fryer
03 .09.2026
To sell air fryers on Amazon, obtain FCC (US), UL, FDA, CE (EU), RoHS, GS (Germany), UKCA, PSE (Japa...
EU Toy Safety Standard EN 71-1:2026 EU Toy Safety Standard EN 71-1:2026
03 .09.2026
EN 71‑1:2026 updates toy mechanical/physical safety rules; JJR Lab tests gaps, stability, brakes, ve...
Introduction to EU Toy Standards EN 71‑1 to EN 71‑ Introduction to EU Toy Standards EN 71‑1 to EN 71‑
03 .09.2026
EN 71 ensures EU toy safety via physical (EN71‑1), fire (EN71‑2), chemical (EN71‑3) tests; JJR lab o...
Amazon Canada Site / SOR Children's Products Compl Amazon Canada Site / SOR Children's Products Compl
03 .09.2026
Amazon Canada requires children’s products meet SOR/2018-83, SOR/2016-188, SOR/2016-193 & ASTM F...

Leave Your Message